add orca slicer
add klipper files
This commit is contained in:
284
modules/services/printer/printer.cfg
Normal file
284
modules/services/printer/printer.cfg
Normal file
@@ -0,0 +1,284 @@
|
||||
# This file contains pin mappings for the stock Sovol SV06.
|
||||
#
|
||||
# Find installation instructions at https://github.com/bassamanator/Sovol-SV06-firmware
|
||||
#
|
||||
# See https://www.klipper3d.org/Config_Reference.html for configuration reference.
|
||||
|
||||
[include ./osskc.cfg]
|
||||
[include ./timelapse.cfg]
|
||||
#[include ./cfgs/adxl-rp2040.cfg]
|
||||
|
||||
[mcu]
|
||||
# NOTE Obtain definition by "ls -l /dev/serial/by-id/"
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 250
|
||||
max_accel: 2800
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 45
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
[input_shaper]
|
||||
shaper_freq_x: 56.0
|
||||
shaper_type_x: zv
|
||||
shaper_freq_y: 55.4
|
||||
shaper_type_y: 2hump_ei
|
||||
|
||||
#####################################################################
|
||||
# X/Y/Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC2
|
||||
dir_pin: !PB9
|
||||
enable_pin: !PC3
|
||||
microsteps: 128
|
||||
rotation_distance: 40
|
||||
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
||||
position_endstop: 0
|
||||
position_max: 223 # NOTE You can adjust this if you have more room
|
||||
homing_speed: 40
|
||||
homing_retract_dist: 0
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC1
|
||||
run_current: 0.860
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
driver_SGTHRS: 81
|
||||
diag_pin: PA5
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PC3
|
||||
microsteps: 128
|
||||
rotation_distance: 40
|
||||
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
||||
position_endstop: 0
|
||||
position_max: 223 # NOTE You can adjust this if you have more room
|
||||
homing_speed: 40
|
||||
homing_retract_dist: 0
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC0
|
||||
run_current: 0.900
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
driver_SGTHRS: 81
|
||||
diag_pin: PA6
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB6
|
||||
dir_pin: !PB5
|
||||
enable_pin: !PC3
|
||||
microsteps: 128
|
||||
rotation_distance: 4
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -4
|
||||
position_max: 258 # NOTE You can adjust this if you have more room
|
||||
homing_speed: 5
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PA15
|
||||
run_current: 1.000
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
diag_pin: PA7
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
[extruder]
|
||||
step_pin: PB4
|
||||
dir_pin: !PB3
|
||||
enable_pin: !PC3
|
||||
microsteps: 128
|
||||
rotation_distance: 4.65 # NOTE Calibrate e-steps https://www.klipper3d.org/Rotation_Distance.html#calibrating-rotation_distance-on-extruders, https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#calibrate-esteps
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PA1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC5
|
||||
#control: pid
|
||||
#pid_kd: 86.991
|
||||
#pid_kp: 21.479
|
||||
#pid_ki: 1.326
|
||||
min_temp: 0
|
||||
max_temp: 300
|
||||
max_extrude_only_distance: 150.0
|
||||
max_extrude_cross_section: 5 # NOTE Needed for KAMP purge
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC14
|
||||
run_current: 0.550
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA2
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
#control: pid
|
||||
#pid_kp: 64.440
|
||||
#pid_ki: 0.773
|
||||
#pid_kd: 1343.571
|
||||
min_temp: 0
|
||||
max_temp: 110
|
||||
|
||||
#####################################################################
|
||||
# Probe Related
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
pin: PB1
|
||||
x_offset: 27
|
||||
y_offset: -20
|
||||
#z_offset: 0
|
||||
samples: 3
|
||||
samples_result: median
|
||||
samples_tolerance: 0.01
|
||||
samples_tolerance_retries: 5
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 84.50, 135 # NOTE The probe is at the center of the bed.
|
||||
speed: 100.0
|
||||
z_hop: 10
|
||||
z_hop_speed: 15
|
||||
|
||||
[bed_mesh]
|
||||
speed: 175
|
||||
mesh_min: 27, 6 # probe as close to origin as possible while remaining fully on the bed
|
||||
mesh_max: 222, 203 # (x.position_max - 1), (y.position_max - abs(y_offset)) ; probe as far as possible from the origin while remaining fully on the bed
|
||||
probe_count: 5,5
|
||||
algorithm: bicubic
|
||||
fade_start: 1
|
||||
fade_end: 10
|
||||
fade_target: 0
|
||||
|
||||
[axis_twist_compensation]
|
||||
calibrate_start_x: 27 # probe x coor at furthest left ; abs(x_offset)
|
||||
calibrate_end_x: 195 # probe x coor at furthest right ; (x.position_max - abs(x_offset) - 1)
|
||||
calibrate_y: 115
|
||||
|
||||
#####################################################################
|
||||
# Fans
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
pin: PA0
|
||||
|
||||
#####################################################################
|
||||
# Misc
|
||||
#####################################################################
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: PB12
|
||||
sclk_pin: PB13
|
||||
sid_pin: PB15
|
||||
encoder_pins: ^PB14, ^PB10
|
||||
click_pin: ^!PB2
|
||||
|
||||
[bed_screws]
|
||||
screw1_name: front left
|
||||
screw1: 26.5, 31
|
||||
screw2_name: front right
|
||||
screw2: 196.75, 31
|
||||
screw3_name: back right
|
||||
screw3: 196.75, 201
|
||||
screw4_name: back left
|
||||
screw4: 26.5, 201
|
||||
|
||||
[screws_tilt_adjust]
|
||||
screw1_name: center
|
||||
screw1: 84.50, 135
|
||||
screw2_name: front left
|
||||
screw2: 0, 51
|
||||
screw3_name: front right
|
||||
screw3: 169.75, 51
|
||||
screw4_name: back right
|
||||
screw4: 169.75, 221
|
||||
screw5_name: back left
|
||||
screw5: 0, 221
|
||||
horizontal_move_z: 10
|
||||
screw_thread: CCW-M4
|
||||
|
||||
[output_pin beeper]
|
||||
pin: PC6
|
||||
value: 0
|
||||
shutdown_value: 0
|
||||
pwm: True
|
||||
cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
|
||||
|
||||
[filament_switch_sensor filament_sensor]
|
||||
switch_pin: PA4 # "Pulled-high"
|
||||
pause_on_runout: True
|
||||
insert_gcode:
|
||||
M117 Insert Detected
|
||||
{ action_respond_info("Insert Detected") }
|
||||
runout_gcode:
|
||||
M117 Runout Detected
|
||||
{ action_respond_info("Runout Detected") }
|
||||
CONDITIONAL_BEEP i=3 dur=300 freq=400
|
||||
|
||||
[skew_correction]
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 68.420
|
||||
#*# pid_ki = 1.068
|
||||
#*# pid_kd = 1095.581
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 22.905
|
||||
#*# pid_ki = 1.483
|
||||
#*# pid_kd = 88.472
|
||||
#*#
|
||||
#*# [probe]
|
||||
#*# z_offset = 1.410
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# -0.052344, -0.023750, -0.024063, -0.022500, -0.039219
|
||||
#*# -0.029688, -0.011563, -0.011406, -0.013750, -0.048750
|
||||
#*# -0.038750, -0.023281, -0.039375, -0.036875, -0.067188
|
||||
#*# -0.035156, -0.035000, -0.035781, -0.034375, -0.065313
|
||||
#*# -0.024688, -0.015781, -0.011406, -0.021094, -0.022500
|
||||
#*# x_count = 5
|
||||
#*# y_count = 5
|
||||
#*# mesh_x_pps = 2
|
||||
#*# mesh_y_pps = 2
|
||||
#*# algo = lagrange
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 27.0
|
||||
#*# max_x = 222.0
|
||||
#*# min_y = 6.0
|
||||
#*# max_y = 203.0
|
||||
#*#
|
||||
#*# [skew_correction CaliFlower]
|
||||
#*# xy_skew = -0.0001004783772044709
|
||||
#*# xz_skew = 0.0
|
||||
#*# yz_skew = 0.0
|
||||
Reference in New Issue
Block a user