285 lines
6.6 KiB
INI
285 lines
6.6 KiB
INI
# This file contains pin mappings for the stock Sovol SV06.
|
|
#
|
|
# Find installation instructions at https://github.com/bassamanator/Sovol-SV06-firmware
|
|
#
|
|
# See https://www.klipper3d.org/Config_Reference.html for configuration reference.
|
|
|
|
[include ./osskc.cfg]
|
|
[include ./timelapse.cfg]
|
|
#[include ./cfgs/adxl-rp2040.cfg]
|
|
|
|
[mcu]
|
|
# NOTE Obtain definition by "ls -l /dev/serial/by-id/"
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 250
|
|
max_accel: 2800
|
|
max_z_velocity: 15
|
|
max_z_accel: 45
|
|
square_corner_velocity: 5.0
|
|
|
|
[input_shaper]
|
|
shaper_freq_x: 56.0
|
|
shaper_type_x: zv
|
|
shaper_freq_y: 55.4
|
|
shaper_type_y: 2hump_ei
|
|
|
|
#####################################################################
|
|
# X/Y/Z Stepper Settings
|
|
#####################################################################
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
microsteps: 128
|
|
rotation_distance: 40
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 223 # NOTE You can adjust this if you have more room
|
|
homing_speed: 40
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC1
|
|
run_current: 0.860
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
driver_SGTHRS: 81
|
|
diag_pin: PA5
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PB7
|
|
enable_pin: !PC3
|
|
microsteps: 128
|
|
rotation_distance: 40
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 223 # NOTE You can adjust this if you have more room
|
|
homing_speed: 40
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC0
|
|
run_current: 0.900
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
driver_SGTHRS: 81
|
|
diag_pin: PA6
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC3
|
|
microsteps: 128
|
|
rotation_distance: 4
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: -4
|
|
position_max: 258 # NOTE You can adjust this if you have more room
|
|
homing_speed: 5
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PA15
|
|
run_current: 1.000
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
diag_pin: PA7
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
[extruder]
|
|
step_pin: PB4
|
|
dir_pin: !PB3
|
|
enable_pin: !PC3
|
|
microsteps: 128
|
|
rotation_distance: 4.65 # NOTE Calibrate e-steps https://www.klipper3d.org/Rotation_Distance.html#calibrating-rotation_distance-on-extruders, https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#calibrate-esteps
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PA1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC5
|
|
#control: pid
|
|
#pid_kd: 86.991
|
|
#pid_kp: 21.479
|
|
#pid_ki: 1.326
|
|
min_temp: 0
|
|
max_temp: 300
|
|
max_extrude_only_distance: 150.0
|
|
max_extrude_cross_section: 5 # NOTE Needed for KAMP purge
|
|
pressure_advance: 0.05
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC14
|
|
run_current: 0.550
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
heater_pin: PA2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
#control: pid
|
|
#pid_kp: 64.440
|
|
#pid_ki: 0.773
|
|
#pid_kd: 1343.571
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
#####################################################################
|
|
# Probe Related
|
|
#####################################################################
|
|
|
|
[probe]
|
|
pin: PB1
|
|
x_offset: 27
|
|
y_offset: -20
|
|
#z_offset: 0
|
|
samples: 3
|
|
samples_result: median
|
|
samples_tolerance: 0.01
|
|
samples_tolerance_retries: 5
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 84.50, 135 # NOTE The probe is at the center of the bed.
|
|
speed: 100.0
|
|
z_hop: 10
|
|
z_hop_speed: 15
|
|
|
|
[bed_mesh]
|
|
speed: 175
|
|
mesh_min: 27, 6 # probe as close to origin as possible while remaining fully on the bed
|
|
mesh_max: 222, 203 # (x.position_max - 1), (y.position_max - abs(y_offset)) ; probe as far as possible from the origin while remaining fully on the bed
|
|
probe_count: 5,5
|
|
algorithm: bicubic
|
|
fade_start: 1
|
|
fade_end: 10
|
|
fade_target: 0
|
|
|
|
[axis_twist_compensation]
|
|
calibrate_start_x: 27 # probe x coor at furthest left ; abs(x_offset)
|
|
calibrate_end_x: 195 # probe x coor at furthest right ; (x.position_max - abs(x_offset) - 1)
|
|
calibrate_y: 115
|
|
|
|
#####################################################################
|
|
# Fans
|
|
#####################################################################
|
|
|
|
[fan]
|
|
pin: PA0
|
|
|
|
#####################################################################
|
|
# Misc
|
|
#####################################################################
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PB12
|
|
sclk_pin: PB13
|
|
sid_pin: PB15
|
|
encoder_pins: ^PB14, ^PB10
|
|
click_pin: ^!PB2
|
|
|
|
[bed_screws]
|
|
screw1_name: front left
|
|
screw1: 26.5, 31
|
|
screw2_name: front right
|
|
screw2: 196.75, 31
|
|
screw3_name: back right
|
|
screw3: 196.75, 201
|
|
screw4_name: back left
|
|
screw4: 26.5, 201
|
|
|
|
[screws_tilt_adjust]
|
|
screw1_name: center
|
|
screw1: 84.50, 135
|
|
screw2_name: front left
|
|
screw2: 0, 51
|
|
screw3_name: front right
|
|
screw3: 169.75, 51
|
|
screw4_name: back right
|
|
screw4: 169.75, 221
|
|
screw5_name: back left
|
|
screw5: 0, 221
|
|
horizontal_move_z: 10
|
|
screw_thread: CCW-M4
|
|
|
|
[output_pin beeper]
|
|
pin: PC6
|
|
value: 0
|
|
shutdown_value: 0
|
|
pwm: True
|
|
cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin: PA4 # "Pulled-high"
|
|
pause_on_runout: True
|
|
insert_gcode:
|
|
M117 Insert Detected
|
|
{ action_respond_info("Insert Detected") }
|
|
runout_gcode:
|
|
M117 Runout Detected
|
|
{ action_respond_info("Runout Detected") }
|
|
CONDITIONAL_BEEP i=3 dur=300 freq=400
|
|
|
|
[skew_correction]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 68.420
|
|
#*# pid_ki = 1.068
|
|
#*# pid_kd = 1095.581
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 22.905
|
|
#*# pid_ki = 1.483
|
|
#*# pid_kd = 88.472
|
|
#*#
|
|
#*# [probe]
|
|
#*# z_offset = 1.410
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -0.052344, -0.023750, -0.024063, -0.022500, -0.039219
|
|
#*# -0.029688, -0.011563, -0.011406, -0.013750, -0.048750
|
|
#*# -0.038750, -0.023281, -0.039375, -0.036875, -0.067188
|
|
#*# -0.035156, -0.035000, -0.035781, -0.034375, -0.065313
|
|
#*# -0.024688, -0.015781, -0.011406, -0.021094, -0.022500
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = lagrange
|
|
#*# tension = 0.2
|
|
#*# min_x = 27.0
|
|
#*# max_x = 222.0
|
|
#*# min_y = 6.0
|
|
#*# max_y = 203.0
|
|
#*#
|
|
#*# [skew_correction CaliFlower]
|
|
#*# xy_skew = -0.0001004783772044709
|
|
#*# xz_skew = 0.0
|
|
#*# yz_skew = 0.0
|