nbf5: add klipper config

hosts/nbf5/hardware-configuration.nix

@@ -134,13 +134,9 @@
   networking = {
     useDHCP = false;                        # Deprecated
     hostName = "nbf5";
-    wireless.iwd.enable = true;
-    networkmanager = {
-      enable = true;
-      wifi = {
-        backend = "iwd";
-        powersave = true;
-      };
+    wireless = {
+      iwd.enable = true;
+      interfaces = [ "wlan0" ];
     };
     interfaces = {
       wlan0 = {

modules/services/printer/firmware.conf

@@ -0,0 +1,110 @@
+CONFIG_LOW_LEVEL_OPTIONS=y
+# CONFIG_MACH_AVR is not set
+# CONFIG_MACH_ATSAM is not set
+# CONFIG_MACH_ATSAMD is not set
+# CONFIG_MACH_LPC176X is not set
+CONFIG_MACH_STM32=y
+# CONFIG_MACH_HC32F460 is not set
+# CONFIG_MACH_RP2040 is not set
+# CONFIG_MACH_PRU is not set
+# CONFIG_MACH_AR100 is not set
+# CONFIG_MACH_LINUX is not set
+# CONFIG_MACH_SIMU is not set
+CONFIG_BOARD_DIRECTORY="stm32"
+CONFIG_MCU="stm32f103xe"
+CONFIG_CLOCK_FREQ=72000000
+CONFIG_SERIAL=y
+CONFIG_FLASH_SIZE=0x10000
+CONFIG_FLASH_BOOT_ADDRESS=0x8000000
+CONFIG_RAM_START=0x20000000
+CONFIG_RAM_SIZE=0x5000
+CONFIG_STACK_SIZE=512
+CONFIG_FLASH_APPLICATION_ADDRESS=0x8007000
+CONFIG_STM32_SELECT=y
+CONFIG_MACH_STM32F103=y
+# CONFIG_MACH_STM32F207 is not set
+# CONFIG_MACH_STM32F401 is not set
+# CONFIG_MACH_STM32F405 is not set
+# CONFIG_MACH_STM32F407 is not set
+# CONFIG_MACH_STM32F429 is not set
+# CONFIG_MACH_STM32F446 is not set
+# CONFIG_MACH_STM32F765 is not set
+# CONFIG_MACH_STM32F031 is not set
+# CONFIG_MACH_STM32F042 is not set
+# CONFIG_MACH_STM32F070 is not set
+# CONFIG_MACH_STM32F072 is not set
+# CONFIG_MACH_STM32G070 is not set
+# CONFIG_MACH_STM32G071 is not set
+# CONFIG_MACH_STM32G0B0 is not set
+# CONFIG_MACH_STM32G0B1 is not set
+# CONFIG_MACH_STM32G431 is not set
+# CONFIG_MACH_STM32G474 is not set
+# CONFIG_MACH_STM32H723 is not set
+# CONFIG_MACH_STM32H743 is not set
+# CONFIG_MACH_STM32H750 is not set
+# CONFIG_MACH_STM32L412 is not set
+# CONFIG_MACH_N32G452 is not set
+# CONFIG_MACH_N32G455 is not set
+# CONFIG_MACH_STM32F103x6 is not set
+CONFIG_MACH_STM32F1=y
+CONFIG_HAVE_STM32_USBFS=y
+CONFIG_HAVE_STM32_CANBUS=y
+CONFIG_STM32F103GD_DISABLE_SWD=y
+CONFIG_STM32_DFU_ROM_ADDRESS=0
+# CONFIG_STM32_FLASH_START_2000 is not set
+# CONFIG_STM32_FLASH_START_5000 is not set
+CONFIG_STM32_FLASH_START_7000=y
+# CONFIG_STM32_FLASH_START_8000 is not set
+# CONFIG_STM32_FLASH_START_8800 is not set
+# CONFIG_STM32_FLASH_START_9000 is not set
+# CONFIG_STM32_FLASH_START_10000 is not set
+# CONFIG_STM32_FLASH_START_800 is not set
+# CONFIG_STM32_FLASH_START_1000 is not set
+# CONFIG_STM32_FLASH_START_4000 is not set
+# CONFIG_STM32_FLASH_START_0000 is not set
+CONFIG_STM32_CLOCK_REF_8M=y
+# CONFIG_STM32_CLOCK_REF_12M is not set
+# CONFIG_STM32_CLOCK_REF_16M is not set
+# CONFIG_STM32_CLOCK_REF_20M is not set
+# CONFIG_STM32_CLOCK_REF_24M is not set
+# CONFIG_STM32_CLOCK_REF_25M is not set
+# CONFIG_STM32_CLOCK_REF_INTERNAL is not set
+CONFIG_CLOCK_REF_FREQ=8000000
+CONFIG_STM32F0_TRIM=16
+# CONFIG_STM32_USB_PA11_PA12 is not set
+CONFIG_STM32_SERIAL_USART1=y
+# CONFIG_STM32_SERIAL_USART1_ALT_PB7_PB6 is not set
+# CONFIG_STM32_SERIAL_USART2 is not set
+# CONFIG_STM32_SERIAL_USART2_ALT_PD6_PD5 is not set
+# CONFIG_STM32_SERIAL_USART3 is not set
+# CONFIG_STM32_SERIAL_USART3_ALT_PD9_PD8 is not set
+# CONFIG_STM32_CANBUS_PA11_PA12 is not set
+# CONFIG_STM32_CANBUS_PA11_PB9 is not set
+# CONFIG_STM32_MMENU_CANBUS_PB8_PB9 is not set
+# CONFIG_STM32_MMENU_CANBUS_PD0_PD1 is not set
+CONFIG_SERIAL_BAUD=250000
+CONFIG_USB_VENDOR_ID=0x1d50
+CONFIG_USB_DEVICE_ID=0x614e
+CONFIG_USB_SERIAL_NUMBER="12345"
+CONFIG_WANT_GPIO_BITBANGING=y
+CONFIG_WANT_DISPLAYS=y
+CONFIG_WANT_SENSORS=y
+CONFIG_WANT_LIS2DW=y
+CONFIG_WANT_LDC1612=y
+CONFIG_WANT_HX71X=y
+CONFIG_WANT_ADS1220=y
+CONFIG_WANT_SOFTWARE_I2C=y
+CONFIG_WANT_SOFTWARE_SPI=y
+CONFIG_NEED_SENSOR_BULK=y
+CONFIG_CANBUS_FREQUENCY=1000000
+CONFIG_INITIAL_PINS=""
+CONFIG_HAVE_GPIO=y
+CONFIG_HAVE_GPIO_ADC=y
+CONFIG_HAVE_GPIO_SPI=y
+CONFIG_HAVE_GPIO_I2C=y
+CONFIG_HAVE_GPIO_HARD_PWM=y
+CONFIG_HAVE_STRICT_TIMING=y
+CONFIG_HAVE_CHIPID=y
+CONFIG_HAVE_STEPPER_BOTH_EDGE=y
+CONFIG_HAVE_BOOTLOADER_REQUEST=y
+CONFIG_INLINE_STEPPER_HACK=y

modules/services/printer/klipper.nix

@@ -10,28 +10,31 @@
     services = {
       klipper = {
         enable = true;
-	configFile = "./printer.cfg";
-	#firmwares."sovol06" = {
-	#  serial = "/dev/usb/by-id/123";
-	#  enableKlipperFlash = true;
-	#  enable = true;
-	#  configFile = "./firmware.conf";
-	#};
+	configFile = ./printer.cfg;
+	firmwares."sovol06" = {
+	  serial = "/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0";
+	  enableKlipperFlash = true;
+	  enable = true;
+	  configFile = ./firmware.conf;
+	};
       };
 
       mainsail = {
         enable = true;
 	nginx = {
-	  enableACME = true;
-	  useACMEHost = "home.opel-online.de";
-	  serverName = "sv06.home.opel-online.de";
-	  onlySSL = true;
+	  enableACME = false;
+	  #useACMEHost = "home.opel-online.de";
+	  serverName = "nbf5.home.opel-online.de";
+	  #onlySSL = true;
 	  listenAddresses = [ "0.0.0.0" "::" ];
-	  forceSSL = true;
+	  #forceSSL = true;
         };
       };
 
-      moonraker.enable = true;
+      moonraker = {
+        enable = true;
+	allowSystemControl = true;
+      };
 
 #      nginx = {
 #        enable = true;