Markdown-reflow to prevent long lines
This commit is contained in:
hoijui
@@ -1,7 +1,8 @@
|
||||
# Build Guide
|
||||
|
||||
This is the build guide for Corne Chocolate.
|
||||
[Click here for Corne Cherry](https://github.com/foostan/crkbd/blob/master/corne-cherry/doc/buildguide_en.md).
|
||||
[Click here for Corne Cherry](
|
||||
https://github.com/foostan/crkbd/blob/master/corne-cherry/doc/buildguide_en.md).
|
||||
|
||||
## Parts
|
||||
|
||||
@@ -38,8 +39,11 @@ This is the build guide for Corne Chocolate.
|
||||
|
||||
## Preparation
|
||||
|
||||
If you build the firmware yourself, it will take some time to set up the environment, so it's best to start at the beginning. \
|
||||
For more information, please see https://github.com/foostan/crkbd/blob/master/doc/firmware_en.md.
|
||||
If you build the firmware yourself,
|
||||
it will take some time to set up the environment,
|
||||
so it's best to start at the beginning. \
|
||||
For more information,
|
||||
please see <https://github.com/foostan/crkbd/blob/master/doc/firmware_en.md>.
|
||||
|
||||
## Building
|
||||
|
||||
@@ -59,13 +63,15 @@ Mounting on the front will interfere with the top plate.
|
||||
Since the diodes are very small,
|
||||
it is easier to work with tweezers and inverted tweezers.
|
||||
Since the **mounting orientation of the diode is crucial**,
|
||||
it is possible to proceed smoothly if you arrange the columns and rows to be mounted in advance,
|
||||
it is possible to proceed smoothly
|
||||
if you arrange the columns and rows to be mounted in advance,
|
||||
as shown in the following photo.
|
||||
|
||||
|
||||
|
||||
The orientation of the diode is as follows.
|
||||
Attach the chip component so that the "|||" mark on the diode is facing the "|" of the diode mark "| ◁" on the PCB (image from Corne Cherry).
|
||||
Attach the chip component so that the "|||" mark on the diode is facing the "|"
|
||||
of the diode mark "|◁" on the PCB (image from Corne Cherry).
|
||||
|
||||
|
||||
|
||||
@@ -76,7 +82,8 @@ First put solder only on the right side of the pad.
|
||||
|
||||
Next, solder one of the diodes by melting the solder you already put on the board.
|
||||
At this time,
|
||||
it is recommended that you use inverted tweezers so that you can hold the SMD part firmly without applying force,
|
||||
it is recommended that you use inverted tweezers
|
||||
so that you can hold the SMD part firmly without applying force,
|
||||
and concentrate on alignment and soldering instead.
|
||||
Also, if the soldering iron is too hot or the solder is touched too long,
|
||||
the flux contained in the solder may evaporate and a solder pile may be formed,
|
||||
@@ -127,7 +134,8 @@ If so, you cna fix the jumper by applying more solder or separate flux.
|
||||
|
||||
|
||||
|
||||
Solder the pin headers to the white frame and solder the Pro Micro with back side up.
|
||||
Solder the pin headers to the white frame
|
||||
and solder the Pro Micro with back side up.
|
||||
|
||||
|
||||
|
||||
@@ -142,7 +150,8 @@ please refer to the [Helix Build Guide](https://github.com/MakotoKurauchi/helix/
|
||||
Insert the pin header into the OLED pin socket first,
|
||||
then solder the pin header and the OLED module.
|
||||
At this time,
|
||||
make sure that he OLED module sits tightly on the socket while holding it down with your finger,
|
||||
make sure that he OLED module sits tightly on the socket
|
||||
while holding it down with your finger,
|
||||
because it tends to stick out easily.
|
||||
|
||||
|
||||
@@ -150,16 +159,21 @@ because it tends to stick out easily.
|
||||
|
||||
### Operation check
|
||||
|
||||
We recommend that you check the operation at the stage where the Pro Micro and OLED modules are attached (it is difficult to isolate the problem at the end).
|
||||
We recommend that you check the operation at the stage
|
||||
where the Pro Micro and OLED modules are attached
|
||||
(it is difficult to isolate the problem at the end).
|
||||
|
||||
Before checking the correct operation,
|
||||
flash the crkbd firmware to the Pro Micro by referring to the [Firmware](#firmware) section below
|
||||
flash the crkbd firmware to the Pro Micro
|
||||
by referring to the [Firmware](#firmware) section below
|
||||
(be sure to insert it on both sides).
|
||||
|
||||
Operation confirmation is performed by connecting the left hand side to a PC with Micro USB
|
||||
Operation confirmation is performed
|
||||
by connecting the left hand side to a PC with Micro USB
|
||||
and connecting the left hand side and the right hand side with a TRS cable.
|
||||
Since there may be a defect such as a jack,
|
||||
make sure to connect the left and right instead of one by one before checking the operation.
|
||||
make sure to connect the left and right
|
||||
instead of one by one before checking the operation.
|
||||
If you have done this correctly,
|
||||
short-circuit the pad to attach the PCB socket with tweezers,
|
||||
and the key pressed on the OLED module will be displayed.
|
||||
@@ -176,12 +190,14 @@ so if you are worried about mounting it,
|
||||
we recommend that you skip this chapter and complete it first.
|
||||
|
||||
SK6812MINI is very heat sensitive and breaks easily.
|
||||
We recommend using a soldering iron with a temperature control function and operating at a temperature of about 220°C to 270°C.
|
||||
We recommend using a soldering iron with a temperature control function
|
||||
and operating at a temperature of about 220°C to 270°C.
|
||||
Even if the temperature is set that low,
|
||||
the LED will be damaged if the iron is left on it for a long time,
|
||||
so try to solder as quickly as possible.
|
||||
Solder four LEDs at a time,
|
||||
but we recommend soldering two at a time instead of four at a time to prevent the LED temperature from rising,
|
||||
but we recommend soldering two at a time instead of four at a time
|
||||
to prevent the LED temperature from rising,
|
||||
as this will make it less likely to overheat.
|
||||
|
||||
First, check the mounting position.
|
||||
@@ -194,13 +210,15 @@ Below is the location to attach the LED (image from Corne Cherry).
|
||||
|
||||
|
||||
For LEDs 1 to 6,
|
||||
solder the part so that the black part circled below is on the bottom and the silk mark indicated by the arrow is on the top.
|
||||
solder the part so that the black part circled below is on the bottom
|
||||
and the silk mark indicated by the arrow is on the top.
|
||||
Note that the direction changes between 1 - 3 and 4 - 5.
|
||||
|
||||
|
||||
|
||||
For 7 - 27,
|
||||
perform soldering so that the largest pad surrounded by a circle and the silk mark indicated by an arrow are adjacent to each other,
|
||||
perform soldering so that the largest pad surrounded by a circle
|
||||
and the silk mark indicated by an arrow are adjacent to each other,
|
||||
as shown below.
|
||||
|
||||
|
||||
|
||||
Reference in New Issue
Block a user